Bse V9 Flash File MT6572 5.0.1 Firmware

Download Zip https://t.co/HgWi135IYa



(Rooting and flashing TWRP) OR (flashing TWRP/custom recovery) triggers Knox rendering warranty void
. That is how Samsung works (Does rooting (but no custom roms) trigger knox's void warranty). Flashing a custom ROM would also trigger Knox. There are workarounds mostly involving apps(of the one click variety), that use exploits and may or not work and hence not recommending them. If warranty not being void is important to you, please experiment and decide. Odin method is safe but trips Knox once you flash custom recovery



Custom Recovery
. IMO, 
TWRP
 is the best in terms of it being easiest to use and also reliability. Download TWRP from the official website. One of many tutorials on net show how to root and 
flash TWRP



Now, you are all set for unlocking bootloader, rooting and flashing TWRP on your mother mobile. Once you are done, double check if rooted fully using apps like Root Checker. Configure mother mobile in terms of freezing unwanted apps, installing apps you need, setting up the user interface the way you want, launchers etc. Take two backups. First backup would be a complete back up or image This is ONLY to backup your mother mobile. Second back up or image would be WITHOUT EFS, and would be used for flashing on rest of devices. As already pointed out in another answer, EFS is device specific and flashing complete backup like the first back up discussed, on to any other device would almost certainly result in losing IMEI and emphatically not recommended (Tip: while backing up do not enable MD5 check option, it vastly increases imaging time without adding much value)


Now, coming to imaging on other devices. Copy the second image file (without EFS) on an ext SD or internal storage as you prefer and install image using TWRP. You could even take help from one or two of the bright, dependable end users and get done quickly. Typically a 3 gig image can be flashed in about 6 minutes, so two of you can get the job of populating images done in about 3 hours



IMPORTANT NOTE:
 Far as I know there is something that must be taken care of cautiously about Samsungs when flashing/restoring/backing up ROMs that are 
EFS files
. EFS files are the files that include your IMEI number 
and they are strictly device-specific.
 Therefore I can't tell for sure but predict that flashing a back-up with EFS files of another phone can be problematic. I would suggest asking about it on Stack Overflow since they'll know better about it.


Recently I was asked to clone USB flash drive (4GB). This drive contains two paritions: first is UDF (1.3GB) - which Windows 7 sees as CD-ROM drive, and the second is Fat32(2.7GB) - which looks and behaves like a normal removable device. When I open Windows Disk Management it shows two separate devices - CD-ROM and removable device with one Fat32 partition.





I have a brand new board which is a clone of the Mega2560. I need to install the USB firmware on the 16U2 and the bootloader on the 2650 chip. I have Atmel Studio and a JTAGICE-3. Using those, I can download HEX files compiled with the Arduino IDE, and they run successfully.


But I'm having trouble finding Mega-specific instructions for getting the firmware installed so that I can use the Arduino ISP protocol for downloading new sketches. I can find much more information about the Uno than the Mega. And much of the information I do find seems to be dated.


First of, MEGA-dfu_and_usbserial_combined.hex is, as stated on the github page, for the 8u2, not the 16u2. Since you already have a ISP programmer you don't need the dfu functionality. You can just flash the precompiled Arduino-usbserial-atmega16u2-Mega2560-Rev3.hex file.


My Alfawise EX8 (Anet A8 Clone) had an issue, so I flashed the firmware prov

Bse V9 Flash File MT6572 5.0.1 Firmware

Egadfarcji